Travel distances, positions, speeds, operating times - easily defined with the new web-based control system for drylin® E linear systems from igus®.
All relevant documents - flyers and technical data, latest firmware, operating instructions, CANopen Electronic Data Sheet, 2D and 3D drawings - can be found in the shop on the page of the corresponding product under downloads.
Logic and load supply are separate in order to enable safety shutdown.
The logic voltage supply is 12-24V and the load voltage supply is 12-48V.
With the 10 predefined inputs, movements can be selected, started and stopped. Due to two limit switches input, the motor control system can perform safety functions as well.
With the 5 predefined outputs, information can be obtained from the motor control system. The motor control system indicates whether it is ready or carrying out a movement, has been referenced or whether there are any alarms or faults.
Two analogue inputs can be used to read absolute position information of a linear axis, or to specify speeds or positions. An "electronic hand wheel" can be used to cause a linear axis to travel without any parameter changes having to be made.
The motor connection is suitable for, DC, 3-phase EC and 2-phase stepper motors. A connection for a motor brake has also been integrated into this connector.
In order to enable optimum motor control and specification of an exact position, an angular encoder is needed. The motor control system has been designed for many different types of angular encoder with a voltage supply of 5V.
The CANopen connection is a communication protocol used to communicate with higher-level control systems. It is used to control individual axes but primarily to operate multi-axis systems. drylin® E linear robots can be operated effectively and efficiently with CANopen.
The Ethernet port is used to call up the graphic user interface via a browser or to communicate via Modbus TCP as gateway.
The LED status display provides information on the IP address or on the status of the control systems.
For example, it automatically outputs the IP address of the motor control system or shows warnings or error messages.
You can use the intuitive browser user interface to set the travel mode, positions, rates of acceleration, speed and pause times of your linear axis.
Test the simulated user interface of the motor controller here. When you use the real control system, your input is transmitted exactly as in this simulator. There is no separate transmission.
It's that easy: Under 'Travel profiles', you can configure up to eight lines and apply the control parameters to the linear axis. In the 'Mode' field, use HOM to set the zero point or use ABS to define the absolute position for movement on the linear axis. Choose the destination by entering the position on the axis or by using the Teach function. Enter the values for acceleration, speed and deceleration and, if necessary, a pause time. Under 'Subsequent block', specify the number of the next travel profile.
The dryve motor control system can either be connected to your network or you can connect it directly to the control unit (PC or PLC) by means of a network cable. You can then start the control system directly in the browser without software installation. Settings can therefore be made in one minute.
For each linear axis you need one dryve motor control system.
You can use the simple intuitive user interface to parameterise travel distances, position, feed and operating time of your linear axis even as an amateur.
Movements that are continuously repeated are known as looping can be set in just a few seconds. A teach function enables position settings to be made with just one mouse click.
With standardised communication protocols such as CANopen or Modbus TCP as gateway, it is easy to connect the system to industrial controllers such as Siemens S7 or Beckhoff.
The ten digital inputs and outputs enable extremely easy communication with industrial controllers but also with low-price open-source modules such as Arduino or Raspberry Pi.
dryve supports DC, EC and stepper motors both in open loop and closed loop technology.
The supply voltage of up to 48 V ensures high motor speeds. The nominal current of 7 A and the peak current of 20 A results in powerful and dynamic movements.
|Nominal voltage logic supply||12–24V DC|
|Nominal voltage load supply||12V DC|
|Motor types||Two-phase stepper motor bipolar (ST), direct current motor (DC),|
electrically commutated motor (EC)
|Continuous motor current||7A|
|Peak motor current||ST: 10A, DC: 14A, EC: 21A max. 2 sec depending on frequency of movement|
|Load power output||max. 340W continuous|
|Digital output current||max. 200mA per output|
|Holding brake||24V DC/1A|
|Angular encoder||Hall sensor (two or three poles), encoder (line driver-RS422 or single ended)|
analogue feedback via analogue inputs
|Digital inputs||10 digital inputs, preassigned function, choice of NPN or PNP,|
built-in pull-down (PNP) and pull-up (NPN) resistor
short-circuit-proof, electrically separated, 5–24V DC (external)
|Digital outputs||Five digital outputs, preassigned function, choice of PNP,|
built-in pull-down resistor,
short-circuit-proof, electrically separated, 5-24V DC (external)
|Analogue inputs||Two analogue inputs, ±10V DC signal (12 bit), 0-10V DC signal (11 bit),|
10V DC voltage supply
|Interfaces||CANopen (DS 402), Modbus TCP as gateway (CiA 309), Ethernet, bit coding, cycle/direction|
|Operating modes||Open-loop with/without position monitoring, closed-loop|
|Operating modes||Binary: 32 travelling movements Tipp/|
Teach: Up to 8 individual positioning movements.
Step/direction: external Stipulation of set point
|CE symbol acc. to EMC guideline||EN 61000-6-2:2005, EN 61000-6-3:2007|
|Ambient temperature||-20°C to +45°C|
|Relative humidity||≤ 90%, non-condensating|
|Maximum temperature of the power unit||100°C|
|Bearing temperature||-40°C to +60°C|
|Protection class||IP 30|
|Protective functions||Power unit temperature monitoring, current monitoring,|
undervoltage and overvoltage protection, contouring error detection, encoder control
|Mounting||Screwed on, top hat (DIN) rail assembly|
|D x W x H in mm|
(incl. connectors and mounting elements)
|124 x 31 x 139|
Ready to ship in 24 - 48 hrs.
Monday to Friday from 7 am - 8 pm.Saturdays from 8 am- 12 pm.